Pro AV Solutions

Video Wall 4K over IP PoE Extender Kit

The Video Wall 4K over IP PoE Extender Kit allows HDMI equipment supporting up to 4K @ 30Hz or 1080p at 60Hz resolution to be connected and extended to create a Video Wall of user configurable size (X by Y) supporting 100’s of screens, depending on network bandwidth, utilizing one Receiver for each display in the array. Each Transmitter (500759-TX) and Receiver (500759-RX) can be connected via Cat5e/6 cable up to 330ft (100m) from an Ethernet Switch. The Transmitters and Receivers support PoE (PD) and may be powered by a PoE (PSE) Ethernet Switch. The kit comes with one (1) Transmitter and one (1) Receiver. The IR Emitter and IR Sensor, if required, may be purchased separately for IR based remote control applications.

HDMI 4K over IP PoE Extender Kit

The HDMI 4K over IP PoE Extender Kit allows HDMI equipment to be extended up to 330ft (100m) up to 4K (3840×2160) resolution @ 30Hz via one (1) Cat5e/6 cable in a point-to-point configuration. Point-to-multipoint and multipoint-to-multipoint configurations are also possible by connecting several units to the same local Ethernet network, and the device supports PoE (PD) if used with a PoE (PSE) Ethernet Switch.

HDMI over IP H.264 PoE Extender Kit

The HDMI over IP H.264 PoE Extender Kit allows HDMI source and display equipment to be connected in point-to-point, point-to-multipoint and multipoint-to-multipoint configurations via a local Ethernet network, in a flexible, expandable and cost effective manner, without the need to install dedicated cabling systems. Connectivity may be up to 330ft (100m) @ 1080p via Cat5e/6 UTP cable, and the device supports PoE (PD) if used with a PoE (PSE) Ethernet Switch

Audio / AMP over IP PoE Extender Kit with Mic

The Audio / AMP over IP PoE Extender Kit with Mic includes a Transmitter (500755-AMP-TX) and a Receiver (500755-AMP-RX) allowing a 2CH analog audio and Mic signal to be extended over an IP network, and up to 330ft (100m) from an Ethernet Switch via Cat5e/6 cable in a point-to-point configuration. Point-to-multipoint and multipoint-to-multipoint is supported by connecting several Transmitters and Receivers to the same local Ethernet network. Depending on the application one or more Transmitters (500755-AMP-TX) can communicate with (or multicast to) multiple Receivers (500755-AMP-RX).The Transmitter supports PoE (PD) if used with a PoE (PSE) Ethernet Switch. Supports RS232 and IR transmission for remote control of end devices

Video Wall over IP Extender Kit

The Video Wall over IP Extender Kit with PoE allows HDMI equipment to be connected to create a Video Wall of a user configurable size (X by Y) supporting 100’s of screens, depending on network bandwidth, utilizing one receiver for each display in the array.
The transmitter unit is connected using a LAN switch (PoE or non-PoE), with maximum distances of 330ft (100m) of Cat5e/6 cable between equipment.
Set-up and configuration of the video wall function is carried out using the MuxLab ProDigital Network Controller (500811) – sold separately.

HDMI / RS232 over IP Extender Kit

The HDMI / RS232 over IP Extender Kit with PoE allows HDMI equipment to be connected up to 330feet (100m) @ 1080p via one (1) Cat5e/6 unshielded twisted pair cable in a point-to-point configuration. Point-to-multipoint and multipoint-to-multipoint is possible by connecting several Transmitters and Receivers to the same Ethernet network. The Transmitter (500753-TX) and Receiver (500753-RX) also support PoE (PD) if used with a PoE (PSE) Ethernet Switch

HDMI over IP Extender Kit

The HDMI over IP Extender Kit with PoE allows HDMI equipment to be connected up to 330feet (100m) @ 1080p via one (1) Cat5e/6 unshielded twisted pair cable in a point-to-point configuration. Point-to-multipoint and multipoint-to-multipoint is possible by connecting several Transmitters and Receivers to the same Ethernet network. The Transmitter (500752-TX) and Receiver (500752-RX) also support PoE (PD) if used with a PoE (PSE) Ethernet Switch. The kit comes with one (1) Transmitter and one (1) Receiver.

ProDigital Network Controller

The MuxLab ProDigital Network Controller is a Linux-based PC that allows users to control hub-installed MuxLab products via an Ethernet Web interface.

When installed on a local area network (LAN), the MuxLab Network Controller will scan the LAN for connected MuxLab products allowing the user to configure and control these products through an Ethernet Web interface.

8 Button RS232/IR Control Panel

The 8 Button RS232/IR Control Panel is a versatile wall or table-top mounted control panel for MuxLab AV devices and third party products. Each button is programmable and works either individually or as part of a group. The unit supports three (3) RS232, one (1) RS485, three (3) Infrared, and two (2) Relay for control of end devices. Units may be chained together to form larger systems. The 8 Button RS232/IR Control Panel can control MuxLab products, as well as third party devices such as projectors and projector screens, displays, AV sources and other similar devices. Products that can be managed by this device are shown below under Related Products.

5×1 HDMI / HDBT Presentation switch

The 5×1 HDMI / HDBT Presentation switch is a compact scaler switcher with 5 video inputs (3 HDMI, 2 VGA) and 6 audio inputs (3 HDMI audio & 2 VGA with audio switched following the video; 1 MIC audio input). The VGA input supports VGA, Component Video (YPbPr) and Composite Video.
The 5×1 HDMI / HDBT Presentation switch scales & switches any video signal to HDMI output and HDBaseT output for a transmission over up to 70 m of Cat5e/6 with PoC support.
With 1 IR Sensor, 5 IR Emitters and 1 RS232 port, bidirectional IR & RS232 signals can be transmitted simultaneously between the 5×1 HDMI / HDBT Presentation switch and the HDMI Extender PoC/PoE Receiver

HDMI 2.0 ready Multimedia 16×16 Matrix Switch

The HDMI 2.0 ready Multimedia 16×16 Matrix Switch is a modular AV switching platform that converts and switches a wide range of digital AV interfaces including 4K @ 60 Hz.
The switch features an 8-slot chassis that allows up to four 4-port input modules to be switched to up to four 4-port output modules for a maximum switching capacity of 16×16.
The matrix switch offers control via front LCD touch panel, RS232, USB, IR, web server interface, or third party control system. The dual-redundant power supply design reduces the potential for down- time. The matrix switch is compatible with MuxLab HDBaseT transmitters and receivers for I/O distribution of signals over distance.

Analog Audio Balun Amplifier

The MuxLab Analog Audio Balun Amplifier allows one (1) analog audio source using one of the MuxLab Hi-Fi Audio Baluns to feed a compact 30W per channel stereo Class D Amplifier using a single Cat5e/6 cable to distances of up to 3,250ft / 1km.
With a simple OSD showing graphical input level (left & right) and volume level. Push and turn button on front of unit for power on/off and volume.
Compatible with MuxLab transmitter baluns: 500028, 500028-WP-US, 500028-WP-UK, or 500028-F; or the MuxLab 8×8 Line Level Audio Matrix Switch (500210).

Audio Zone Amplifier 100W

The MuxLab Audio Zone Amplifier 100W is a Class D amplifier which allows analog or digital sources to feed a pair of 50W per channel speakers. When set in Bridge mode and paired with the MuxLab 70V Transformer unit (500755-70V), the system is compatible with distributed 70V speaker systems over longer distances and supporting daisy chain configurations. The device may be controlled locally via pushbuttons and a knob, and remotely via RS232, IR and an IP webserver interface.

The Audio Zone Amplifier features two analog 2CH audio inputs (RCA & 3.5mm) & one (1) PCM digital optical input (TosLink), along with two 50W 8Ω speaker outputs or one 100W 4Ω speaker output (terminal block).

Audio Zone Amplifier

The MuxLab Audio Zone Amplifier is a Class D digital amplifier that allows one (1) analog source to be distributed to a pair of 20W per channel stereo speakers within a zone. The Audio Zone Amplifier can be cascaded infinitely across multiple zones to give a multi-room audio solution.
The Audio Zone Amplifier features two (2) stereo analog audio input lines, microphone input with 48V phantom supply, and two (2) 20W, 4-ohm speaker outputs or one (1) 40W, 8-ohm speaker output.
Volume and source control via the front push buttons, or via IR using the optional IR Sensor & Handheld Remote Control Kit (500216-IR).

8 x 8 Cat 5e/6 Line Level Audio Matrix Switch

The 8 x 8 Cat 5e/6 Line Level Audio Matrix Switch supports audio switching between multiple audio sources and distribution via Cat 5e/6 cable.
The Cat 5e/6 Line Level Audio Matrix Switch provides full non-blocking port switching and distribution between multiple stereo line level analog audio sources. The Audio Matrix Switch uses RJ45 connectors and works in conjunction with MuxLab’s stereo audio balun (500019, 500027, 500028 and 500030) and digital audio balun (500020).
The product provides port buffering, unity gain compensation and ground loop isolation. The Switch can be managed via push-button, IR, RS232, Ethernet, Web Server, or 3rd

Analog Stereo Audio Splitter

The Analog Stereo Audio Splitter allows one analog source using either the Muxlab analog audio balun (500028) or Muxlab Audio Matrix Switch (500210) to be connected passively to up to three receivers using Muxlab’s Analog Audio Balun (500028) over CAT 5e/6 cabling.

Digital Audio Converter

The MuxLab Digital Audio Converter (500088) has been designed to decode and downmix Dolby® Digital and DTS audio signal transmissions to 2ch analog stereo.
Input from either a Digital Coax (S/PDIF) or Digital Optical (TOSlink) source such as a Smart TV, BluRay player, or satellite receiver to convert the digital signal to a 2 channel analog output.

Digital Audio Converter

The MuxLab Digital Audio Converter (500087) is a versatile digital audio standards converter*.
The product allows one (1) Digital Coax (S/PDIF), or Digital Optical (TOSLINK) source to be connected to a Digital Audio Receiver supporting either Digital Coax (S/PDIF), or Digital Optical (TOSLINK) inputs.
The converter supports most standards to transmit two channels of uncompressed lossless PCM audio or compressed 5.1/7.1 surround sound, such as Dolby® Digital Plus or DTS-HD High Resolution Audio (multichannel digital audio Dolby Digital® 5.1, DTS, and Dolby® True HD).

Digital Audio Extender Kit

The MuxLab Digital Audio Extender Kit (500086) is a versatile digital audio standards extender and converter*.

The product allows one (1) Digital Coax (S/PDIF), or Digital Optical (TOSLINK) source to be connected to a Digital Audio Receiver supporting either Digital Coax (S/PDIF), or Digital Optical (TOSLINK) inputs. Outputs on the 500086 receiver unit are simultaneous.

The audio transmission signal can be distributed to up to a distance of 500 ft / 150m in a point-to-point configuration over single Cat5e/6.

Digital Audio Converter

The MuxLab Digital Audio Converter (500081) has been designed to decode and downmix Dolby® Digital* audio signal transmissions to 2ch analog stereo.
Input from either a Digital Coax (S/PDIF) or Digital Optical (TOSlink) source such as a Smart TV, BluRay player or satellite receiver to convert the digital signal to a 2 channel analog output.

Digital Audio Converter

The MuxLab Digital Audio Converter (500080), converts one LPCM-encoded Digital Coax (S/PDIF) or Digital Optical (TOSlink) audio signal to a standard left/right analog audio output (RCA).
This allows a digital audio source such as a BluRay, games console or CD player without a stereo audio output to be connected to an amplifier or TV.

Quad Audio Balun

The MuxLab Quad Audio Balun (500033) allows up to four (4) individual RCA, or two (2) stereo RCA, line-level audio signals to be extended via single Cat5e/6 cable in a point-to-point connection to distances of up to 3,250ft / 1km.
Used in pairs, the Quad Audio Balun eliminates the requirement for additional cable infrastructure, allowing audio equipment to be connected via a single cost-effective Cat5e/6 cable.
The Quad Audio Balun is compatible with the MuxLab 500033-WP-US (Decora™) and the 500033-WP-UK where a convenient wall plate is required, and also works in conjunction with other MuxLab stereo audio baluns such as the 500019 (single RCA) or the 500028 (dual RCA).

MuxLab PC / Audio Balun

The MuxLab PC / Audio Balun (500030) allows an unbalanced line-level stereo audio signal to be transmitted via single Cat5e/6 cable in a point-to-point connection to distances of up to 5,000ft / 1.5km.
The product is designed for audio equipment requiring a 3.5mm line-level stereo input / output such as PC soundcards, laptops, MP3 players and media speakers where the mid-range audio frequency response is paramount.
Used in pairs, the PC Audio balun can also be used with the 500027 stereo audio balun to connect a 3.5mm interface to an RCA audio interface (or vice-versa).

Stereo Hi-Fi Balun

The MuxLab Stereo Hi-Fi Balun (500028) allows an unbalanced line-level Hi-Fi stereo analog audio signal to be transmitted via single Cat5e/6 cable in a point-to-point connection to distances of up to 3,250ft / 1km.
The product is designed for audio applications where full-range, hi-fidelity audio frequency response is required.
Used in pairs, the Stereo Hi-Fi Balun can be used with the 500028-F (female RCA connectors) or the 500028-WP-UK/US as a neat wall-plate solution.

Stereo Audio Balun

The MuxLab Stereo Audio Balun (500027) allows an unbalanced line-level stereo analog audio signal to be transmitted via single Cat5e/6 cable in a point-to-point connection to distances of up to 5,000ft / 1.5km. The product is designed for audio applications where mid-range audio frequency response is paramount.
Used in pairs, the Stereo Audio balun can also be used with the 500030 audio balun to connect an RCA interface to a 3.5mm audio interface (or vice-versa).

Digital Audio Balun

The MuxLab Digital Audio Balun (500020) allows a digital audio source to be connected at distances of up to 600ft / 183m away from a digital audio receiver via single Cat5e/6 cable. Used in pairs, the Digital Audio Balun allows a digital audio source such as BluRay, media servers, gaming consoles, or satellite receivers to be connected to a digital audio system (AVR / digital amplifier) in a point-to-point scenario using digital coax (RCA) connectors.

Analog Audio Balun

The MuxLab Analog Audio Balun (500019) allows any unbalanced audio signal to be transmitted via a single Cat5e/6 to distances of up to 5,000ft / 1.5km. Used in pairs, the Audio Balun eliminates costly and bulky coax cable, allowing consumer and commercial audio equipment to be connected using standard premises wiring techniques.
One or two pairs of baluns are required depending on whether the application is for mono or stereo audio. The Audio Balun features screw terminals for ease of installation and reliable connectivity.

DisplayPort 1.2a Fiber Extender Kit

The DisplayPort 1.2a Fiber Extender Kit, 500502 enables the user to transmit WQUXGA (3840×22400) video at 60Hz signal up to 330ft (100m), with any form of scaling or data compression being applied to the signal. This device support a total data throughput of 21.6Gbps (5.4Gbps per lane).

DisplayPort 1×2 Splitter

The DisplayPort 1×2 Splitter (500505) allows one DisplayPort 1.2a source to be distributed to two (2) DisplayPort displays. The splitter supports video resolutions up to 4K and PCM Audio up to 7.1-Channel and up to 192 kHz sampling rate.